Plumbing Basics: A Prerequisite for When Installing a Bathtub
Plumbing Basics: A Prerequisite for When Installing a Bathtub
Blog Article
What're your opinions on A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't precisely rocket science, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bathtub with a brand-new one is also a moderately challenging project. If the old bathtub is conveniently easily accessible, the project can move speedily; if you need to open a wall to remove the old bathtub and also position the new tub, the job is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will certainly need an assistant to vacate the old bathtub as well as set in the new one. Make sure you have actually certified on your own for the job as well as fit attempting it. Instead of hiring a specialist to take over a halfway-completed project, it is far better to think about using one before you begin. Opportunities are you might require an expert plumber to make tube links.
This write-up will help you set up a brand-new tub in your washroom if you have already gotten a new tub and do not require to transform the setup of your previous water supply pipes.
Your tools and product list must consist of the following:
Preparing for the Installation
To start with, the sustaining structure supplied with the bathroom should be fitted (if called for) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps device to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be fitted in its last setting.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited gain access to that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bathtub in the needed position. The wood boards are helpful in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four tiny factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the spirit level as well as adjusting the feet on the bathtub until the spirit level reviews level.
To install faucets, fit all-time low of the outermost versatile faucet port to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the water supply and also check all joints and new pipework for leakages and tighten them if needed. Fill up the bath tub as well as also inspect the overflow outlet and the normal electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's user's manual. Tiling and also securing around the bathtub needs to wait till the bath tub has actually been used at the very least once as this will settle it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, after that you will require a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in location between the tap and the sink. Safeguard the tap in place with the manufacturer provided backnut. Once the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type should be connected to the faucet ends first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can move enough to fracture an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, bring about difficulties with wetness as well as possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your components and also fittings. They are marketed in tubes and also cartridges, and can securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill the bath tub with water before sealing, to allow for the activity experienced when the tub is in usage. The sealer can crack relatively early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily offered on the market. It is a good idea to fit the floor tiles using waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our part about Installing A Bathtub. Thanks a ton for taking a few minutes to read our article. In case you enjoyed our blog posting kindly remember to share it. Thanks a lot for your time. Visit again soon.
Ready to help! Report this page